Your Position: Home - Hardware - What is the Pipe Fittings？
Piping or plumbing is the occupation of installing or repairing systems of pipes or fittings that convey liquids, gases, and occasionally solid materials. and connects to the end of the pipe so that it can change direction, control flow, and change the diameter of the pipe.
The variety of pipe fittings can be as confusing as choosing the right screws or nails for a construction project. The materials vary, and the specific uses, while precise, can seem daunting. The following is a brief overview of what pipe fittings are used for and the materials offered.
Elbow. Used to change the angle or direction at which a pipe runs. The most common are 90- and 45-degree turns. The sweep of the fitting describes the speed at which the transition or change of direction is made.
Street Elbow. A fitting that has a male thread on one end and a female thread on the other. These are common in galvanized steel and copper pipe. They are convenient because they don't require nipples and they work well in tight places.
Tee Fittings. Shaped like the letter T to allow for branching lines.
Splice. Used to connect two straight pieces of tubing of the same diameter.
Reducer: Used to connect pipes of different diameters. Used to connect pipes of different diameters. Makes the diameter change gradually.
Bushing: Used to make the diameter of a pipe fitting smaller. Used to make the diameter of a fitting smaller. They are different from reducers because they make a sudden change in diameter and take up less space.
Unions. Used to connect tubing that cannot be rotated, or that must be removed for maintenance or equipment replacement.
Adapter. Used to change the end of a non-threaded pipe to a male or female thread, as needed. Most commonly used for work with copper and plastic pipe.
Pipe Cap. Used to seal the end of a dead-end pipe.
Plug: Used to seal the end of a dead-end pipe. Used to close the end of a fitting that is normally used for inspection or cleaning.
Nipples: Used to close the end of a fitting that is normally used for inspection or cleaning. A short length of pipe that has threads on both ends.
Wrench: Primarily used to gain access to the inside of a pipe. Primarily used to gain access to the inside of DWV (drain-waste-ventilator) systems.
Valve: A device that controls the flow of liquid. A device that controls the flow of liquid or gas through or out of a pipe. (Compression valves, ball valves, sleeve valves, ceramic disc valves, etc.).
PVC Fittings. Available in a variety of configurations, either glued (S) or threaded (T).
Copper Fittings. Use compression fittings. Common fittings are fittings, elbows, and tees.
The application of pipe fittings is everywhere, and it is very good to find a supplier that can provide high-quality products; other flanged valves pls visit website.
924
0
2
Comments
All Comments (0)
Popular Articles
Applications Of Heavy Weight Drill Pipe
Heavy weight drill pipe (HWDP) is usually run in between the drill collars and the drill pipe in order to prevent fatigue of the drill pipe in the vertical drilling industry.Hebei longway is a professional Heavy Weight Drill Pipe Supplier.Contact us to discuss your requirements.
By CC
223
0
0
Guidelines for Types and Materials of Fuel Lines
The fuel line is a safety part of every car and therefore must comply with safety regulations. There are a few considerations drivers should be aware of when selecting a reliable fuel line, with minimal verification at the component level.
By Geym
180
0
0
Are cotton tents right for you?
It is good camping practice to weather a new cotton tent before use or after a long spell of storage. You soak the tent either by rain or the use of a hose. It is then left to dry naturally before repeating the process several times.
By Marie
213
0
0
Did You Know The Facts About Galvanized Wire?
Galvanized wire is a type of metal wire that is galvanized. It offers many advantages and benefits over other types of wire, making it a popular choice for a variety of applications. Here, we will discuss some of the key reasons to use galvanized iron wire.
By Marie
179
0
0
Related Articles
Wafer type butterfly valves VS flange kind butterfly valves
The butterfly plate of the wafer type butterfly valve is set up in the diameter instructions of the pipeline. In the round channel of the butterfly valve body, the disc-shaped butterfly plate turns around the axis and the turning angle is between 0 ° and 90 °, which can play the duty of flow policy.
By CC
5
0
0
What are the three types of hose clamps?
Hose clamps are a critical component of fluid control systems, used to secure hoses and tubing onto fittings and connectors.
By Geym
8
0
0
Thread Repair Methods and Tools for Vehicle Parts
Thread Repair Methods and Tools for Vehicle Parts Threaded holes can be found in all areas of your vehicle, from the engine to the chassis.
By Geym
8
0
0
What Is The Wafer Type Butterfly Valve?
The butterfly plate of the wafer type butterfly valve is set up in the diameter instructions of the pipeline. In the round channel of the butterfly valve body, the disc-shaped butterfly plate turns around the axis and the turning angle is between 0 ° and 90 °, which can play the duty of flow policy.
By CC
13
0
0